Milkit - set valve tubeless, presta 55mm

Scrie o recenzie
  • Milkit vezi mai multe
    In stoc depozit
    mkDV5
  • PRP   : 17500 lei
    12800 lei include 21% TVA Ai gasit un pret mai bun?

    Produsele aflate in stoc se livreaza in 3-5 zile lucratoare. Produsele in stoc depozit se livreaza in cca 5-7 zile lucratoare. Atentie - In perioada sarbatorilor de iarna (17/12/2024 - 10/01/2025), livrarea se va realiza in interval de minim 8 zile lucratoare.

    Plata cu cardul online
    Plata cu cardul online prin Mobilpay
    Plata ramburs
    Rate prin StarBT
    Rate prin Garanti Bank
    Rate prin Alpha Bank
    Rate prin First Bank
    Rate prin Raifeissen
    Plata in rate prin TBI Bank
    Ordin de plata

    Pentru unitatile care se supun Legii Achizitiilor Publice, oferim posibilitatea achizitionarii produselor si prin Sistemul Informatic Colaborativ pentru Achizitii Publice - SICAP/SEAP

    Depunem eforturi permanente pentru acuratetea informatiilor. Totusi, dorim sa precizam ca poza produsului are un caracter informativ. Unele specificaţii din descriere sau caracteristici pot fi modificate de catre producător fără un preaviz sau pot conţine erori de operare.

    • Comanda Telefonica:

    0769 064 522

    Livrare: 19 lei (oriunde in tara)

    Ajunge in 1-3 zile

Produse din aceeasi categorie

Banda adeziva pentru janta de inalta presiune Schwalbe 18 mm
Banda adeziva pentru janta de inalta presiune Schwalbe 18 mm
300 lei
Banda janta High Pressure HPM, 26 inch, 23 × 559/571, 1620 mm, albastru
Banda janta High Pressure HPM, 26 inch, 23 × 559/571, 1620 mm, albastru
300 lei
Fond de janta 28 inch 125cm 18mm
Fond de janta 28 inch 125cm 18mm
300 lei
Fond de janta Force 27.5 584-18 2 bucati negru
Fond de janta Force 27.5 584-18 2 bucati negru
600 lei
Fond de janta 27.5 inch 23x584-622 1690mm
Fond de janta 27.5 inch 23x584-622 1690mm
700 lei
Kit valve pompa BBB BFP-9001
Kit valve pompa BBB BFP-9001
1500 lei

Descriere

Milkit valves make using tubeless systems clean and easy


  • easy - refill sealant through the valve – tire stays inflated without the valve core
  • quick - check sealant levels while the tire stays inflated
  • clean - tires are mounted dry and the valve design prevents clogging


NO MESS & NO AIR LOSS, EVEN WITHOUT THE VALVE CORE

milKit patented tubeless valve system is quick and easy to use:


  • Smart rubber flaps ensure no air is lost when the valve core is removed and sealant does not block the valves
  • Use the syringe to easily check if enough sealant remains in your tire
  • The syringe accurately measures the amount of sealant needed
  • No more mess as tires can be installed dry and sealant added afterwards through the valve
  • Kit contains measuring & refilling syringe, valves, and valve core removal tool


How to use MILKIT VALVES & SYRINGE?

This patented system enables clean and easy tubeless tire setup.


Install valve and screw out the milKit valve core

Pre-inflate your tire up to 22 psi (we recommend the milKit Booster) – the rubber flaps ensure no air is lost even with the valve core removed

(For maintenance rather than installation of new tire) Extract old sealant from tire with the milKit syringe to measure remaining amount and check quality

Measure out the correct amount of sealant and inject using the syringe

Screw the valve core back in, inflate tire to full pressure until the tire fully jumps onto the rim and you’re ready to ride!

The solution to combat sealant drying out or escaping! With other tubeless tire valve systems you need to remove the tire to check if enough sealant remains, with milKit you can simply remove the valve core and insert the syringe to check. No mess and faster results!


The syringe holds 60ml or 2 oz of fluid and comes with a flexible connector and a large needle to push through the valve and rubber flaps. There’s also a sealant regulator that screws into the syringe for easy refilling. The needle has an angled end for effective removal of all sealant in the tire.


Patented milKit presta bike valves are made in Germany from anodized high quality aluminum alloy and high performance rubber for the smart flaps.


The standard milKit valves have a usable length of 35 mm (1 3/8 inch), and they work for most road and mountain bike rims except some special high-profile rims. For high-profile rims, there are 45mm, 55mm and 75mm versions of the milKit valves available.


milKit valves can be used with most sealants, but we recommend milKit sealant.

This has been specially designed for best results with these valves.


Replacement valves & valve cores are also available.


MILKIT VALVE 55mm pack includes:

  • 2x 55mm milKit valves
  • 1x valve core tool
  • 2x milKit rim stickers

Recenzii

Nu au fost găsite recenzii